Description

Candela GentleLase Laser Heads are packaged and ready for fast delivery. no need to send your old laser head.

CALH1436

THIS LASER HEAD WILL FIT THE FOLLOWING MACHINE

1 GENTLELASE PLUS GLP

2 MINI GENTLELASE MGL

3 MINI GENTLEYAG MGY

This is a  NEW laser head , not refurbishes or rebuild . all parts are brand new , all new metal parts,  all new : Flash Lamps, Triple Bore Flow Tube, Reflector, Light Blocking Hardware and O-ring Seals.
These laser head are all  individually performance tested in the factory. They show excellent output energy .

New Laser Heads greatly increase the useful life of the entire laser system, substantially lowering voltages required for the same output energies.

Laser rod is NOT included.

we also offer installation of you laser rod and testing, refurbish your laser rod, rework your laser rod.

• When your system setting can not achieve the setting and the power you request.
• When you hear a thumping sound or when you do not get enough speed and energy during treatment.

New laser head include:

• New metal and new water monifold
• New flash lamps
• New triple bore
• New seal kit include all o-rings
• New light blocking kit
• New flow tubes
• Applying and re-coating with reflective powder.

We can also supply Yag and Alex laser heads and other laser rods if needed.

CANDELA ALEXANDRITE LASER HEAD ALEX ROD 755NM ROD , CARD1341

LASER HEAD REPLACEMENT
NOTE: Exercise extreme care. Cleanliness of optics is essential. Refer to
Service Procedure 8503-01-0060 for optic cleanliness. Refer to drawing 7121-99-
6700, 7121-99-6780 and 7122-99-3298 for specific details.
Avoid the need to clean the optics other than by gently blowing the dust off of them
with filtered, compressed nitrogen or air. If the laser rod needs cleaning, gently wipe
with methanol, acetone, or propanol.
CAUTION: This laser system does not have a fast discharge high voltage dump
resistor. It takes approximately 16 minutes for the high voltage to discharge from
2000 VDC to 40 VDC. To discharge the high voltage quickly, set the HV to 0 volts
when the actual voltage is greater than 1000 volts and pulse the laser. HOWEVER,
DO NOT PULSE THE LASER AT A VOLTAGE THAT WILL GIVE > 60j OF HEAD
ENERGY. WAIT FOR THE HEAD TO BLEED DOWN. This will discharge it to less
than 100 VDC but not to zero. 100 volts can be lethal with this size capacitor. Wait
until the voltage is less than 40 volts before using a shorting stick. Never work on
the high voltage components until the voltage is measured as zero and a
shorting stick is across the capacitor terminals to ground.
1. The laser must be OFF. Check the high voltage and verify that is at 0 Volts. Unplug
the laser.
2. Remove the top skin. Remove the Laser Rail dust cover.
3. Remove the two fluid lines from the Laser Head.
4. Remove the Lamp trigger wire from the Laser Head.
5. Remove the HV wires and/or trigger assist wires and/or flashlamp wires connected to
the Laser Head.
6. Remove the four screws that secure the Laser Head to the Monolithic Rail.
7. Remove the Laser Head from the Laser Rail.
8. Install the New Laser Head to the Monolithic Laser Rail. Refer to 7121-99-6700,
7121-99-6780 and 7122-99-3298drawing for specific details. Tighten screws until the
lock washers just start to compress. Do not flatten lock washers.
9. Perform an alignment verification; for GL systems refer to Service Procedure 8503-
01-0610; for GL PLUS, GL 18mm and GL LE refer to Service Procedure 8503-01-
0690; for MGL refer to Service Procedures 8503-01-0825 and 8503-01-0826.

Candela GentleLase Laser Head Information

There are several reasons why the laser head can go bad. First, a water leak in the laser head can cause pressure to build up and break the laser rod, which is a device through which the laser goes and cause the rod to crack. One singular crack can make the laser head stop working.

Secondly, there is a reason why we are adamant about the laser being in a spotless-clean environment. If there is a small spec of dust on the optics, the laser will make contact with the dust and thus gradually burn your optic until the laser has nowhere to go except backwards or sideways, which can cause additional components to break. Additionally, dust can also burn laser rod, and even the laser head. It is also important to note that the flow tubes or triple bore can be damaged from water pressure or dust.

Lastly, a Candela GentleLase Pro Laser Head can malfunction or stop working altogether because of a damaged or broken flash lamp. Please pay attention to your lamp life. If you notice your power has decreased significantly, whereby you need more treatments to achieve the same result, it may be time to change your flash lamp.

In order to extend the life of your laser machine, we recommend a preventative maintenance service on your machine every six months. This will help ensure the safety of your patients, your investment, and your business, as a broken machine can cause delays and inability to follow through on advertised services or scheduled appointments.

Parts4laser  is not affiliated, associated, authorized, endorsed by, or in any way officially connected with Candela their affiliates. Any logos and trademarks of third parties that may be found on our website are registered trademarks of their respective owners. The use of any trademark is for identification and reference purposes only and does not imply any association with the trademark holder.